PCFP from NXP >> Specification: IC, I/O EXPANDER 8BIT, , Manufacturer Part No: PCFP. Order Code: Technical Datasheet: ( EN). The PCF provides general-purpose remote I/O expansion for most microcontroller products and disclaimers thereto appears at the end of this data sheet. 22 Nov DATA SHEET. Product specification. Supersedes data of Jul Nov INTEGRATED CIRCUITS. PCF Remote 8-bit I/O.

Author: Jujinn Kashakar
Country: Lithuania
Language: English (Spanish)
Genre: Politics
Published (Last): 23 October 2016
Pages: 312
PDF File Size: 5.96 Mb
ePub File Size: 16.78 Mb
ISBN: 575-3-44376-167-4
Downloads: 97597
Price: Free* [*Free Regsitration Required]
Uploader: Goramar

Serial Clock Pcf8574p datasheet that is used to synchronize all communications on the bus. There are different ways of working around that limitation. To turn off a LED, we will pull its corresponding pin to high.

PCFP Datasheet(PDF) – NXP Semiconductors

Then, in the loop function, it turns each LED on pcf8574p datasheet milliseconds one at the time. This is because the way pcf8574p datasheet I2C works is that the lines are pulled low to communicate and have to be pulled high the reminder of the time.

Ideally, you should also pcf8574p datasheet a nF ceramic capacitor between the VDD pin and ground. My goal, here, is to turn on only one LED at the time. Currently you have JavaScript disabled.

Adding pins to your Arduino using I2C and a PCFP chip | Francois’ Corner

This may be different if you use another Arduino board. Click here for instructions on how datashret enable JavaScript in your browser. Connect to your 5V or 3. Pcf8574p datasheet defined a constant for the chip pcf8574p datasheet Again, VDD means that pin must to be connected to 3. So, to talk to the chip, I will use 0x20 C language notation for 20 in hexadecimal as the chip address.


Simply change that constant value is you configured the chip with a different address. In the setup function, all it does is initializing the Wire pcf8574p datasheet.

The I2C bus requires 2 wires, so 2 pins on the Arduino and 2 pins on datasheer device attached to the bus. Serial Data Line that is pcf8574p datasheet to carry data between the devices on the bus.

Then, it tells the PCF chip what is the new state of all his 8 output pins. Atmel Power Debugger — First impressions. So, there should be only one pin that’s pulled to ground. This will allow the current to flow through the LED connected to P5. I never faced pcf8574p datasheet where I needed dattasheet many pins! The long lead is connected to pcf8574p datasheet VCC 5V line and the short lead is connected to the resistor.

If the value of the bit corresponding to a pin is a 0, then that pin will be turned low to ground. As mentionned in the wiring section, the 2 pins have to be pulled high datawheet a pull-up resistor. In order to post pff8574p, please make sure JavaScript and Cookies pcf8574p datasheet enabled, and reload the page. I used a 2. Another official NXP Datasheet. Pcf8574p datasheet is useful if you want to use many PCFP chips, on the same I2C bus, because it will allow pcf8574p datasheet to give each of them a unique addresses.


Essentially, what the code does is using the Wire library. If the value of the bit for that pin pcf8574p datasheet a 1, then it will be pulled high 5V in this case. Pay attention to the LEDs pct8574p.

If you do like this example, you now pcf8574p datasheet an extra 14 pins to play with 2 X 8 pins – 2 pins on the Arduino for Pcf8574p datasheet bus. Leave a Reply Cancel reply Your email address will not be published.

Access Denied

Save my name, email, and website in this browser for the next time I comment. The pcf8574p datasheet payload is made of 8 bits, one per output pin. Your dtaasheet address datashest not be published. All you have to do is to give then their own address unless you want many chips to do the same thing and use that address to talk pcf8574p datasheet the chip pcf8574p datasheet your code.

On the PCFP, the 2 pins are:.